"Exchange Type" should be "aggressive".ģ0) "Key Life Time limit" should be "86400" seconds.ģ1) "Key Life Data limit" should be "0" Kbytes.ģ2) "Enable Check Point Compatible Vendor ID" should be unticked.ģ3) Click "Phase 2".
#EASYVPN RV320 PASSWORD#
Set "Pre Shared Key" to the password you set in "Setup Cisco RV325 for Cisco Easy VPN client and Shrewsoft VPN client (full VPN)" above(in this documentation, the example is "DoNotUsThisExample").Ģ5) Click "Phase 1". Make sure "Identification Type" is "Any".Ģ4) Click "Credentials". Set "Authentication Method" to "Mutual PSK + XAuth".Ģ1) Under "Local Identity", choose "Key Identifier" for "Identification Type".Ģ3) Click "Remote Identity". Make sure the "Enable WINS" and "Obtain Automatically" checkboxes are ticked.Ģ0) Click "Authentication" tab.
#EASYVPN RV320 WINDOWS#
Make sure "Enable DNS" and the 2 "Obtain Automatically" checkboxes are ticked.ġ9) This is for Windows only: Under "Name Resolution", click "WINS" tab. "NAT Traversal" should be "enabled".ġ1) Under "Client", "NAT Traversal Port" should be "4500".ġ2) Under "Client", "Keep-alive packet rate" should be "15" seconds.ġ3) Under "Client", "IKE Fragmentation" should be "enable".ġ4) Under "Client", "Maximum packet size" should be "540" Bytes.ġ5) Under "Client", "Enable Dead Peer Detection" should be ticked.ġ6) Under "Client", "Enable ISAKMP Failure Notifications" should be ticked.ġ7) Under "Client", "Enable Client Login Banner" should be ticked.ġ8) Click "Name Resolution" tab.
#EASYVPN RV320 DOWNLOAD#
Firefox and Chrome worked in tests.ġ.B) For Fedora 26 GNU/Linux, issue the following commands as root to download and install:Ĥ) Under "General", assign the IP address used by WAN1 of the router (for this documentation, the example is "1.2.3.4") to "Host Name or IP Address".ĥ) Under "General", "Port" should be "500".Ħ) Under "General", "Auto Configuration" should be "ike config pull".ħ) Under "General", "Adaptor Mode" should be "Use a virtual adapter and assigned address".Ĩ) Under "General", "MTU" should be "1380".ĩ) Under "General", "Obtain "Automatically" should be ticked.ġ0) Tick "Client" tab. Please note that Microsoft Edge does not work with the VPN connection. This VPN client was also tested to work with Windows 10.
#EASYVPN RV320 FULL#
Setup Shrewsoft for full tunnel VPN(Windows 7 to 10 and Fedora 26 GNU/Linux)ġ.A) For Windows 7 to 8.1, download Shrewsoft VPN client from (I used version 2.2.2). "Group" should be "Unassigned" and "Domain" should be "Default". If you use a different value from the default 192.168.1.0, please use it instead.ġ2) "Subnet Mask" should be "255.255.255.0".ġ3) "Extended Authentication" should be "Default - Local Database".Ĭreate an user on Cisco RV325 for Cisco Easy VPNģ) Click "Add" under "User Management Table".Ĥ) Give a "Username" and "Password". We'll use WAN1 for VPN access here.ġ1) "IP Address" should be "192.168.1.0". PLEASE USE YOUR OWN DIFFERENT PASSWORD!).Ĩ) Set "Interface" to "WAN1". This is also your group name.Ħ) Disable "Minimum Password Complexity".ħ) Set "Password" to a desired password (for this documentation, it is "DoNotUsThisExample". Setup Cisco RV325 for Cisco Easy VPN client and Shrewsoft VPN client (full VPN)ĥ) Set "Tunnel Name" to "fullvpn".
0 kommentar(er)
